Ceramic Doctor Blade for Coating Machine

• Sheet Former Type: Fourdrinier Wire
• Paper Thickness: Thin Paper
• Automation: Automatic
• Certification: CE
• Customized: Customized
• Condition: New
• Model NO.: SH2020
• Material: HDPE & Carbon Fiber
• Hardness: 1960n/mm(580hv+/-15)
• Edge Height: 1.3mm
• Blade Height: 10-60mm
• Service Life: 3 Months - 9 Months
• Transport Package: Exporting Stand
• Trademark: sunhong
• Origin: Liaoning
• HS Code: 84392000
• Production Capacity: 10sets Per Month

Product Description

Sun Hong Doctor Blade

Major use: Suitable for front of high-speed dryer, parts of composite material not suit.

Key Features: Inlay with high-performance ceramics in front of metal or thesections with serious stickies.

Major uses: Suitable for all rolls from mesh fabric to automatic paper-reel.
Key Features: Microfiber and epoxy fiber, with very good chemical resistance.
Temperature resistance: 185 centigrade.

Major use: Suitable for drying rolls,Yankee rolls in a dryer, cold steel rolls, WC thermal spraying rolls.

Key Features: Softest in all metal blades, better removing dirt, less damaging rolls.

Major use: Suitable for stone rolls and Ebonite rolls in press section.

Key Features: High hardness, with better scraping result, better corrosion-resistance.

Features

Features of Blade

1, Triple tempt for optimum wear resistance.
2, Long service life for an extra clean cut of tissue paper, toilet roll.
3, Precise heat treatment.
4, Excellent cutting longevity and wear resistance.
5, High intensity,high toughness,small thermal deformation.
6, Blades are eliminated unwanted and uncontrollable residual stress.

Finish of side faces

1, With two-sided compound bevel consisting of secondary and primary bevel
2, Geometry of bevel optimized for the application.
3, Polished bevel for minimum friction.

How to protect doctor blade

Problem	Reason	Measure
Uneven wear, frequent blade replacement	1. The surface of roller or dryer is uneven 2. The doctor holder is damaged or dirty 3. Sediment	1. Use a softer blade 2. Clean, repair or replace the doctor holder 3. Use abrasive blade
Excessive wear on middle or edge of blade	1. The blade is not installed on the top of the roller 2. The old blade sinks (or leaves) the roller or dryer	1. Refit or add gasket at the back of blade if necessary 2. Replace the old and sunken blade
Excessive wear at one end of blade	The displacement of blade is not parallel to the axial direction of roller or dryer	Add gasket, if necessary, move bearing and bracket to adjust scraper parallel to axial direction
The blade is worn evenly, but the end face is rough	1. There is deposit on the surface of roller or dryer 2. The pressure of blade is too high 3. The material of blade is too hard	1. Use abrasive blade when necessary 2. Reduce the pressure 3. Use a slightly soft blade
Excessive wear in sheet area	The sheet leaves sediment on the roller or dryer	1. Use abrasive blade when necessary 2. Trim the edge of blade frequently 3. Use blade with slotted end to prevent excessive pressure on both ends of roller or dryer
Excessive wear out of sheet area	The sheet lubricates the roller or dryer	Use blade with slotted end
Local depression	The blade is damaged, electrostatic (discharge/ electrolysis /heating)	Insulate the blade from the holder or use a non-metallic blade
The blade produces burr	1.The material of the blade is too soft 2. The pressure is too high 3. The angle of the blade is too small	1. Use a slightly hard scraper 2. Reduce the pressure 3. Adjust the bearing or bracket to increase the angle, and use the instrument to check and correct the angle

Detailed Photos

Workshop Display

Packaging & Shipping

1.Bubble Film and waste thick fabric wrapping while protecting inside fabric.
2.Wrapped special fabric package outside(air shipping).
3.Composite wooden box(sea shipping).